(3)
after the specimen has been put in place on the carriage&fastened by means
of the clamp， the brush is raised,， the carriage pushed to the rear,，&the
brush lowered to the face of the specimen. the carriage is then drawn forward
by hand at a uniform rate.
3 試樣放在托架上并用夾具固定后，電刷升起,，托架推到后面,，電刷降到試樣表面。然后用手以勻速向前拉動馬車,。
lfy-602a大45°法織物阻燃性能測試儀
主要用途
a法用于紡織品及其他材料在45°狀態下燃燒時其損毀面積和損毀長度的測定,，b法用于測定紡織品在45°狀態下接受熱熔融至規定長度時接觸火焰的次數。
2 刷毛裝置2.1 刷毛裝置為一組底板,，上面拖著一輛小車,，小車運行在底板下表面二邊相平行的軌道上。刷子用鉸鏈裝在底板后面,，垂直地用150g(0.33磅)的壓力加在小車上,。
2.2 刷子由二排硬尼龍硬毛簇左右交錯排列，尼龍硬毛的直徑為0.41mm(0.016英寸),、長19mm(3/4英寸),，每一簇硬毛有20根尼龍硬毛，每英寸4簇。在小車前部有一夾鉗,，刷毛操作時,，可用它將試樣夾在小車上。
2.3 將試樣放在小車上用夾鉗固定住,，抬起刷子,，45°燃燒箱生產廠家，把小車推向后方,，使刷子放到試樣面上,，再用手以均勻的速度將小車向前拉。
lfy-602a大45°法織物阻燃性能測試儀
主要用途
a法用于紡織品及其他材料在45°狀態下燃燒時其損毀面積和損毀長度的測定,，b法用于測定紡織品在45°狀態下接受熱熔融至規定長度時接觸火焰的次數,。
specimen rack (b， fig. 2). the specimen rack provides supports for the
frames in which the specimens are mounted. the angle of inclination is 45°. two
guide pins projecting downward from the cct of the base of the rack travel
in slots provided in the floor of the chamber so that adjustment can be made
for the thickness of the specimen in relation to the flame front. a stop is
provided in the base of the chamber to assist in adjusting the ition of the
rack.
2 樣本架b,，圖2,。樣品架為安裝樣品的框架提供支撐。傾角為45°,。從機架底座中心向下---的兩個導銷在燃燒室地板上的槽中移動,，以便調整試樣相對于火焰的厚度。腔室底部設有止動塊,，以幫助調整齒條的位置,。
|
登錄后臺
滇公網安備 53011202000392